DG411FEUE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 85Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 755mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG411 |
| Pin Count | 16 |
| Number of Channels | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 355μA |
| Max Supply Current | 350μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 125 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 15pF 47pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -105dB @ 1MHz |
| Switch-on Time-Max | 175ns |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG411FEUE+ Overview
This electronic part is conveniently packaged in 16-TSSOP (0.173, 4.40mm Width), making it easy to ship abroad. To ensure high reliability, a new packaging method Tube is used. In Surface Mount, this analog switch is mounted. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operational temperature extended around -40°C~85°C TA. Total terminations are 16. A high-quality output is provided by the electrical component's 4 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. Electronic part bodies are injected with 16 pins. SPST - NC switching circuits are used in these analog switch ics. If you are looking for variants of the digital switch, trying search with DG411. The internal resistance of this digital multiplexer is 85Ohm. Please refer to the datasheets for 16 pins functions. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. An effective Dual, Single supply digital multiplexer. 9V is the lowest voltage that should be fed to the electronic electronic part. If you put voltage higher than 350μA on the digital multiplexer, damage may occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. In the case of dual power supplies, you should connect at least 4.5V.
DG411FEUE+ Features
4 Channels
Switch Circuit: SPST - NC
DG411FEUE+ Applications
There are a lot of Maxim Integrated DG411FEUE+ Analog Switches & Multiplexers ICs applications.
- Multi-Line E1 Interface Cards
- ISDN NT1/TA
- Isolation
- Voice over IP/DSL – Integrated Access Devices, Smart
- Channel Banks
- CSU
- Modems
- PCMCIA cards
- Battery Powered Instruments
- HDTV
