DG411HSDJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 35Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Power Dissipation | 470mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 105 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 105 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 91 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 105ns, 80ns |
| Charge Injection | 22pC |
| Crosstalk | -88dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 90ns |
| Drain to Source Resistance | 25Ohm |
| Normal Position | NO/NC |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| RoHS Status | Non-RoHS Compliant |
DG411HSDJ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). This packaging method provides high reliability because it uses advanced packaging techniques. In Through Hole, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 1:1. Temperatures around -40°C~85°C TA are extended for operation. In total, there are 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. A total of 16 pins are injected into the electrical part body. A SPST - NC switching circuit is used to build these analog multiplexers. As far as internal resistance is concerned, it has 35Ohm. To find out what the 16 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 44V to the switch device in normal circumstances. Analog switch ics with Dual, Single supply type are cost-effective. It is recommended that the electrical component receives a voltage of 13V. The analogue multiplexer may be damaged if voltage is greater than 1μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. When using dual power supplies, you should attach at least 7V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. It is possible to operate 4 inputs. Drain to Source resistance for this electronic component is 25Ohm.
DG411HSDJ Features
1 Channels
Switch Circuit: SPST - NC
Drain-to-Source resistance: 25Ohm
DG411HSDJ Applications
There are a lot of Vishay Siliconix DG411HSDJ Analog Switches & Multiplexers ICs applications.
- Channel Banks
- ATM
- Video signal routing
- Avionics and Military Systems
- Low-Voltage
- Video switching
- Microprocessor controlled systems
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Cable Modem
- Remote Powered Equipment
