DG411HSDJ-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 80Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | DG411 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 105 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 105 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 91 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 105ns, 80ns |
| Charge Injection | 22pC |
| Crosstalk | -88dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 90ns |
| Normal Position | NC |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| RoHS Status | ROHS3 Compliant |
DG411HSDJ-E3 Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tube. The multiplexer is located in Through Hole. Multiplexers and demultiplexers have a ratio of 1:1. Temperatures around -40°C~85°C TA are extended for operation. 16 terminations have been made so far. A electrical component with 1 channels is capable of high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. This electrical component is included in the 16 series of products. Unlike digital switches, these are based on SPST - NC switching circuits. The multiplexer consists of 4 circuits. Search with DG411 if you are looking for analog multiplexer variants. In this multiplexer, the internal resistance is 80Ohm. Please refer to the datasheets for 16 pins functions. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 44V. A cost-effective Dual, Single supply type analogue multiplexer. 13V should be the lowest voltage fed to the electronic component. This digital switch can be operated with a current of 1μA. Putting voltage greater than 1μA on the multiplexer may cause damage. For this switch, a dual supply voltage is feasible, but it must not exceed 22VFor dual power supplies, a voltage of at least 7V should be attached. The outputs of this digital multiplexer are SEPARATE OUTPUT in number.
DG411HSDJ-E3 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
DG411HSDJ-E3 Applications
There are a lot of Vishay Siliconix DG411HSDJ-E3 Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- Modems
- Audio and video switching
- Audio/video switches
- USB 1.1 signal switching circuits
- DVD-R
- Ultrasound
- Relay replacements
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Video signal routing
