DG411HSDN-T1-E4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-VQFN Exposed Pad |
| Number of Pins | 16 |
| Weight | 57.09594mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 80Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.88W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG411 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1μA |
| Power Dissipation | 1.88W |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 105 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 105 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 91 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 105ns, 80ns |
| Charge Injection | 22pC |
| Crosstalk | -88dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 90ns |
| Normal Position | NC |
| Height | 950μm |
| Length | 4mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG411HSDN-T1-E4 Overview
Packed in 16-VQFN Exposed Pad, the electronic component is convenient for shipping overseas. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. A switch device like this is mounted in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operating temperature around -40°C~85°C TA extended. In total, there have been 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. This electronic part can be found in the 16 series. Based on SPST - NC switching circuits, these analog multiplexers work. Using the DG411 search parameter, you can discover variants of the switch. In this multiplexer, the internal resistance is 80Ohm. You can find the functions of the 16 pins in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. Multiplexers should not be powered above 44V in normal situations. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage fed to the electronic component should be 13V. For this digital switch to work, 1μA current would suffice. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. Despite this switch's dual supply capability, its voltage should not exceed 22V. It is recommended that you attach at least 7V to your dual power supply. This analog switch ic utilizes SEPARATE OUTPUT output. A voltage of 15V can be used to operate the electronic component. It is possible to operate 4 inputs.
DG411HSDN-T1-E4 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
DG411HSDN-T1-E4 Applications
There are a lot of Vishay Siliconix DG411HSDN-T1-E4 Analog Switches & Multiplexers ICs applications.
- 65 V DACs
- Cell phones
- Frame Relay Equipment
- CSU
- Battery Powered Instruments
- DVD-R
- SDH
- Intelligent PBX
- ATM
- Routers
