DG411HSDY
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 547.485991mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 35Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Power Dissipation | 600mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 105 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 105 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 91 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 105ns, 80ns |
| Charge Injection | 22pC |
| Crosstalk | -88dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 90ns |
| Normal Position | NO/NC |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
DG411HSDY Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. In order to provide high reliability, an advanced packaging method Tube is used. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 1:1. Temperatures around -40°C~85°C TA are extended for operation. 16 terminations have been made so far. A electrical component with 1 channels is capable of high-quality output. Turning on and running the electrical part should be easy with a 15V voltage supply. Into the electrical component body are injected 16 pins. These analog multiplexers are built based on SPST - NC switching circuits. Analog switches have 35Ohm internal resistance. Datasheets for functions of 16 pins are available. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 44V volts for the multiplexer. A analog switch ic that has a cost-effective Dual, Single supply type. 13V is the lowest voltage the electrical component should receive. Put voltage above 1μA on the multiplexer to cause damage. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. You should attach at least 7V voltage if you are using dual power supply. This analog switch ic utilizes SEPARATE OUTPUT output. There are 4 inputs to be operated.
DG411HSDY Features
1 Channels
Switch Circuit: SPST - NC
DG411HSDY Applications
There are a lot of Vishay Siliconix DG411HSDY Analog Switches & Multiplexers ICs applications.
- Multi-Line E1 Interface Cards
- New designs requiring multiplexer functions
- HDTV
- Intelligent PBX
- Video switching
- Data Acquisition Systems
- Mechanical reed relay replacement
- Channelized and Unchannelized DS3 applications
- CSU
- Transmit
