Parameters |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
80Ohm |
Terminal Finish |
MATTE TIN |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
600mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG411 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Max Supply Voltage |
44V |
Min Supply Voltage |
13V |
Operating Supply Current |
1μA |
Power Dissipation |
600mW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
105 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
12V ±5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
105 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
91 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 12pF |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
105ns, 80ns |
Charge Injection |
22pC |
Crosstalk |
-88dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
90ns |
Normal Position |
NC |
Height |
1.55mm |
Length |
10mm |
Width |
4mm |
RoHS Status |
ROHS3 Compliant |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
547.485991mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2013 |
JESD-609 Code |
e3 |
DG411HSDY-E3 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tube. It is mounted in the position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. In total, there are 16 terminations. By its 1 channels, the electronic component provides high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. It is injected into the electrical part body with 16 pins. Multiplexers built on a SPST - NC switching circuit are built. Use DG411 to search for variants of the digital switches. This digital multiplexer has 80Ohm internal resistance. The functions of 16 pins can be found in the datasheets. This switch device is a typical Multiplexer or Switches. A voltage higher than 44V should not normally be supplied to the switches. The analog switch ic is of the Dual, Single supply type and is cost-effective. A low voltage of 13V should be applied to the electronic component. This digital switch can be operated with a current of 1μA. Put voltage above 1μA on the multiplexer to cause damage. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. For dual power supplies, a voltage of at least 7V should be attached. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. Among the inputs that can be operated are the 4 inputs.
DG411HSDY-E3 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
DG411HSDY-E3 Applications
There are a lot of Vishay Siliconix DG411HSDY-E3 Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- Central office
- PDAs
- Intelligent PBX
- PBXs
- Audio signal routing
- Battery-powered systems
- Medical systems
- DVD-R
- Industrial and process control systems