Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
547.485991mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2012 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
80Ohm |
Terminal Finish |
TIN LEAD |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
600mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
DG411 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Max Supply Voltage |
44V |
Min Supply Voltage |
13V |
Operating Supply Current |
1μA |
Power Dissipation |
600mW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
105 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
12V ±5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
105 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
91 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 12pF |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
105ns, 80ns |
Charge Injection |
22pC |
Crosstalk |
-88dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
90ns |
Normal Position |
NC |
Height |
1.55mm |
Length |
10mm |
Width |
4mm |
RoHS Status |
ROHS3 Compliant |
DG411HSDY-T1 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Surface Mount is where this multiplexer is located. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Temperatures around -40°C~85°C TA are extended for operation. There are 16 terminations totally. The electronic part provides high-quality output because it has 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. It is injected into the electrical part body with 16 pins. Multiplexers built on a SPST - NC switching circuit are built. DG411 can be used to search for analog multiplexer variants. The internal resistance of this digital multiplexer is 80Ohm. To find out what the 16 pins do, please refer to the datasheets. Multiplexer or Switches is a typical switch device. Multiplexers should not be powered above 44V in normal situations. Analog switch ics with Dual, Single supply type are cost-effective. 13V should be the lowest voltage fed to the electronic component. It would be sufficient to run this analogue multiplexer with 1μA current. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. Despite this switch's dual supply capability, its voltage should not exceed 22V. The voltage should be at least 7V if you are using dual power supplies. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. Among the inputs that can be operated are the 4 inputs.
DG411HSDY-T1 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
DG411HSDY-T1 Applications
There are a lot of Vishay Siliconix DG411HSDY-T1 Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- E1 Network Equipment
- Isolation
- Battery-powered systems
- Switching Systems
- Communication systems
- Multiplexers
- Sample hold systems
- CSU
- Data switching