Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
547.485991mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2015 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
80Ohm |
Terminal Finish |
MATTE TIN |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
600mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG411 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
44V |
Min Supply Voltage |
13V |
Operating Supply Current |
1μA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
105 ns |
Voltage - Supply, Single/Dual (±) |
12V ±5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
105 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
91 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 12pF |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
105ns, 80ns |
Charge Injection |
22pC |
Crosstalk |
-88dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
90ns |
Normal Position |
NC |
Height |
1.55mm |
Length |
10mm |
Width |
4mm |
RoHS Status |
ROHS3 Compliant |
DG411HSDY-T1-E3 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Operation at a temperature around -40°C~85°C TA. Total terminations are 16. A 1 channel electronic part produces high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. There is an electrical component included in the 16 series. Unlike digital switches, these are based on SPST - NC switching circuits. The multiplexer consists of 4 circuits. Use DG411 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 80Ohm. The datasheets for the 16 pins explain the functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 44V. The digital multiplexer has a low cost Dual, Single supply. It is recommended that the electrical component receives a voltage of 13V. This multiplexer would work with 1μA current. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. Despite this switch device's dual supply capability, its voltage should not exceed 22V. The voltage should be at least 7V if you are using dual power supplies. The outputs of this digital multiplexer are SEPARATE OUTPUT in number.
DG411HSDY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
DG411HSDY-T1-E3 Applications
There are a lot of Vishay Siliconix DG411HSDY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- Video switching
- Audio and video switching
- Automatic test equipment
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- SONET
- Industrial control systems
- Avionics and Military Systems
- Intelligent PBX
- DSLAMs