banner_page

DG411LDJ-E3

19ns, 12ns SPST - NC 17Ohm Analog Switches DG411 250pA 16-DIP (0.300, 7.62mm)


  • Manufacturer: Vishay Siliconix
  • Nocochips NO: 880-DG411LDJ-E3
  • Package: 16-DIP (0.300, 7.62mm)
  • Datasheet: PDF
  • Stock: 755
  • Description: 19ns, 12ns SPST - NC 17Ohm Analog Switches DG411 250pA 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Through Hole
Mounting Type Through Hole
Package / Case 16-DIP (0.300, 7.62mm)
Number of Pins 16
Supplier Device Package 16-PDIP
Weight 1.627801g
Operating Temperature -40°C~85°C TA
Packaging Tube
Published 2015
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Resistance 50Ohm
Max Operating Temperature 85°C
Min Operating Temperature -40°C
Max Power Dissipation 900mW
Base Part Number DG411
Number of Outputs 4
Number of Channels 4
Number of Circuits 4
Max Supply Voltage 12V
Min Supply Voltage 2.7V
Operating Supply Current 1μA
Nominal Supply Current 1μA
Power Dissipation 900mW
Max Supply Current 1μA
Throw Configuration SPST
Turn On Delay Time 85 ns
Number of Inputs 4
Voltage - Supply, Single/Dual (±) 2.7V~12V ±3V~6V
Supply Type Dual, Single
Turn-Off Delay Time 60 ns
Max Dual Supply Voltage 6V
-3db Bandwidth 280MHz
On-State Resistance (Max) 17Ohm
Min Dual Supply Voltage 3V
Dual Supply Voltage 5V
Multiplexer/Demultiplexer Circuit 1:1
Current - Leakage (IS(off)) (Max) 250pA
Channel Capacitance (CS(off), CD(off)) 5pF 6pF
Switch Circuit SPST - NC
Switch Time (Ton, Toff) (Max) 19ns, 12ns
Charge Injection 5pC
Crosstalk -95dB @ 1MHz
Height 3.81mm
Length 21.33mm
Width 7.11mm
REACH SVHC Unknown
RoHS Status ROHS3 Compliant

DG411LDJ-E3 Overview


The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. A switch device like this is mounted in Through Hole. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~85°C TA extended. By its 4 channels, the electronic component provides high-quality output. Circuits based on SPST - NC switching are used to construct these analog switch ics. A 4 circuit is present in this switch device. Try searching with DG411 to find analog multiplexer variants. In this multiplexer, the internal resistance is 50Ohm. The datasheets for the 16 pins explain the functions. A voltage higher than 12V should not normally be supplied to the switches. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 2.7V. The analogue multiplexer could operate on 1μA current. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 6V. A dual power supply should have at least 3V voltage attached. There are 4 inputs to be operated. Temperatures above 85°C degrees Celsius should not be operated by the multiplexer. This digital multiplexer has 4 outputs. It is offered by suppliers in package 16-PDIP.

DG411LDJ-E3 Features


4 Channels
Switch Circuit: SPST - NC
1μA Supply Current
-3db Bandwidth: 280MHz

DG411LDJ-E3 Applications


There are a lot of Vishay Siliconix DG411LDJ-E3 Analog Switches & Multiplexers ICs applications.

  • Cellular phones
  • Digital cross connects (DSX-1)
  • Audio and video routing
  • Cross Connects
  • Microprocessor controlled systems
  • Fiber to the Home
  • Modems
  • Avionics test equipment
  • Ultrasound
  • Communications systems

Write a review

Note: HTML is not translated!
    Bad           Good