DG411LDQ-T1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 50Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG411 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 3/12/+-5V |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Power Dissipation | 450mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 50 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 35 ns |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 280MHz |
| On-State Resistance (Max) | 17Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 19ns, 12ns |
| Charge Injection | 5pC |
| Crosstalk | -95dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 60ns |
| Normal Position | NC |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG411LDQ-T1 Overview
As the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. High reliability is ensured by the advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Increasing operating temperature to around -40°C~85°C TA. There are 16 terminations totally. The electronic part delivers high-quality output through its 1 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. A total of 16 pins are injected into the body of the electronic part. A SPST - NC switching circuit is used for these analog switches. Try searching for the analog switch ic with DG411 if you are looking for variants. In this multiplexer, the internal resistance is 50Ohm. Please refer to the datasheets for 16 pins functions. The analog multiplexer shown here is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 12V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 2.7V is the lowest voltage that should be fed to the electronic electronic part. 1μA current would be enough for this multiplexer to operate. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. Despite this switch's dual supply capability, its voltage should not exceed 6V. For dual power supplies, a voltage of at least 3V should be attached. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. There are 4 inputs to be operated.
DG411LDQ-T1 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
-3db Bandwidth: 280MHz
DG411LDQ-T1 Applications
There are a lot of Vishay Siliconix DG411LDQ-T1 Analog Switches & Multiplexers ICs applications.
- Remote Powered Equipment
- Sample hold systems
- Switching Systems
- Isolation
- Audio and video routing
- DSUs
- Voice over IP/DSL – Integrated Access Devices, Smart
- Intelligent PBX
- Frame Relay Equipment
- Public switching systems
