DG411LDQ-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Supplier Device Package | 16-TSSOP |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 50Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 450mW |
| Base Part Number | DG411 |
| Number of Outputs | 4 |
| Number of Channels | 4 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Power Dissipation | 450mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 50 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 35 ns |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 280MHz |
| On-State Resistance (Max) | 17Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 19ns, 12ns |
| Charge Injection | 5pC |
| Crosstalk | -95dB @ 1MHz |
| Height | 920μm |
| Length | 5.08mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG411LDQ-T1-E3 Overview
The electrical component comes in 16-TSSOP (0.173, 4.40mm Width) packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have the same number of circuits 1:1. Temperatures around -40°C~85°C TA are extended for operation. The electronic part delivers high-quality output through its 4 channels. These analog multiplexers are built based on SPST - NC switching circuits. A total of 4 circuits make up this switch device. If you are looking for variants of the digital switch, trying search with DG411. It has an internal resistance of 50Ohm. The functions of 16 pins can be found in the datasheets. normally, users should not supply switches with voltages higher than 12V. The digital multiplexer has a low cost Dual, Single supply. In order for the electronic part to function properly, the lowest voltage should be 2.7V. An operating current of 1μA would be sufficient for this switch device. Putting voltage greater than 1μA on the multiplexer may cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 6V. If you are using a dual power supply, you should attach at least 3V. There are 4 inputs to be operated. An environment with a temperature greater than 85°C should not be used to operate the digital switches. The analog switch ics has 4 outputs. It is offered by suppliers in package 16-TSSOP.
DG411LDQ-T1-E3 Features
4 Channels
Switch Circuit: SPST - NC
1μA Supply Current
-3db Bandwidth: 280MHz
DG411LDQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG411LDQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Public switching systems
- Sample-and-hold systems
- RGB switches
- Medical Instrumentation
- Avionics
- Avionics test equipment
- Digital access cross connects
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Cellular phones
- Communication systems
