DG411LDY-T1
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Supplier Device Package | 16-SOIC |
| Weight | 547.485991mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2015 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 50Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 650mW |
| Base Part Number | DG411 |
| Number of Outputs | 4 |
| Number of Channels | 4 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Power Dissipation | 650mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 50 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 35 ns |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 280MHz |
| On-State Resistance (Max) | 17Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 19ns, 12ns |
| Charge Injection | 5pC |
| Crosstalk | -95dB @ 1MHz |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG411LDY-T1 Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. This electronic part offers high-quality output due to its 4 channels. On the other hand, analog switches can be constructed using SPST - NC switching circuits. There are 4 circuits in this switch device. Try searching for the analog switch ic with DG411 if you are looking for variants. An switch multiplexer with 50Ohm internal resistance has a value of 50Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. In a normalsituation, users should not supply the switches with voltage higher than 12V. Analog switch ics with Dual, Single supply type are cost-effective. There should be 2.7V voltage fed to the electrical part below 2.7V. 1μA current would be enough for this multiplexer to operate. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 6V. In the case of dual power supplies, you should connect at least 3V. It is possible to operate 4 inputs. An environment with a temperature greater than 85°C should not be used to operate the digital switches. There are 4 outputs on the analogue multiplexer. It is possible to purchase a 16-SOIC package from suppliers.
DG411LDY-T1 Features
4 Channels
Switch Circuit: SPST - NC
1μA Supply Current
-3db Bandwidth: 280MHz
DG411LDY-T1 Applications
There are a lot of Vishay Siliconix DG411LDY-T1 Analog Switches & Multiplexers ICs applications.
- Mechanical reed relay replacement
- Channelized and Unchannelized DS3 applications
- Precision test equipment
- Audio and video signal routing
- High-Voltage
- Imaging
- Sample-and-hold systems
- Avionics and Military Systems
- Data Acquisition Systems
- Precision instrumentation
