Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
547.485991mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2013 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
50Ohm |
Terminal Finish |
MATTE TIN |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
650mW |
Technology |
BICMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
5V |
Terminal Pitch |
1.27mm |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG411 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Power Supplies |
3/12/+-5V |
Number of Channels |
1 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2.7V |
Operating Supply Current |
1μA |
Power Dissipation |
650mW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
50 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
2.7V~12V ±3V~6V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
35 ns |
Max Dual Supply Voltage |
6V |
-3db Bandwidth |
280MHz |
On-State Resistance (Max) |
17Ohm |
Min Dual Supply Voltage |
3V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
5pF 6pF |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
19ns, 12ns |
Charge Injection |
5pC |
Crosstalk |
-95dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
60ns |
Normal Position |
NC |
Height |
1.55mm |
Length |
10mm |
Width |
4mm |
RoHS Status |
ROHS3 Compliant |
DG411LDY-T1-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Extended operating temperature around -40°C~85°C TA. 16 terminations have been made so far. As a result of its 1 channels, this electronic component provides high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. On the other hand, analog switches can be constructed using SPST - NC switching circuits. Try searching with DG411 if you're looking for variants. The internal resistance of this digital multiplexer is 50Ohm. To find out what the 16 pins do, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 12V. Analog switch ics with Dual, Single supply type are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 2.7V. This multiplexer would work with 1μA current. When the digital multiplexer is charged above 1μA, damage can occur. If put voltage greater than 6V on the multiplexer, damage may be caused to the device. If you are using dual power supplies, you should attach at least 3V. There are SEPARATE OUTPUT outputs on this analog switch ic. There are 4 inputs to be operated.
DG411LDY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
-3db Bandwidth: 280MHz
DG411LDY-T1-E3 Applications
There are a lot of Vishay Siliconix DG411LDY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Medical Instrumentation
- RGB switches
- High speed data transmission line cards
- Audio and video switching
- Multiplexers
- Frame Relay Equipment
- Routers
- PDAs
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Medical