DG412AK
| Parameters | |
|---|---|
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation | 900mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 175 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 5V~44V ±5V~20V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Drain to Source Resistance | 35Ohm |
| Normal Position | NO |
| Height | 3.94mm |
| Length | 19.56mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-CDIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 900mW |
| Technology | CMOS |
| Number of Functions | 4 |
DG412AK Overview
Shipping overseas is convenient due to the electrical component's packing in 16-CDIP (0.300, 7.62mm). The advanced packaging method Tube provides high reliability. Through Hole is where this multiplexer is located. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Temperatures around -55°C~125°C TA are extended for operation. 16 terminations have been made so far. A total of 16 pins are injected into the electrical part body. A SPST - NO switching circuit is used for these analog switches. An switch multiplexer with 35Ohm internal resistance has a value of 35Ohm. To find out what the 16 pins do, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 36V should not normally be supplied to the switches. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage fed to the electronic component should be 13V. A voltage higher than 1μA may cause damage to the switch multiplexer. Despite this switch device's dual supply capability, its voltage should not exceed 22V. You should attach at least 7V voltage if you are using dual power supply. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. The electrical component supports 4 inputs. Drain to Source resistance for this electronic component is 35Ohm.
DG412AK Features
Switch Circuit: SPST - NO
Drain-to-Source resistance: 35Ohm
DG412AK Applications
There are a lot of Vishay Siliconix DG412AK Analog Switches & Multiplexers ICs applications.
- PBXs
- Fiber In The Loop (FITL)
- Voice over IP/DSL – Integrated Access Devices, Smart
- Audio and video routing
- Routers
- Microwave transmission systems
- DSUs
- USB 1.1 signal switching circuits
- Imaging
- Medical Instrumentation
