DG412CUE+

175ns, 145ns SPST - NO 45Ohm Analog Switches BREAK-BEFORE-MAKE DG412 16 Pins 250pA 15V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-DG412CUE+
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 756
Description: 175ns, 145ns SPST - NO 45Ohm Analog Switches BREAK-BEFORE-MAKE DG412 16 Pins 250pA 15V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Number of Terminations	16
Termination	SMD/SMT
ECCN Code	EAR99
Resistance	80Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	457mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	DG412
Pin Count	16
Number of Channels	4
Max Supply Voltage	30V
Min Supply Voltage	10V
Operating Supply Current	100pA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	175 ns
Voltage - Supply, Single/Dual (±)	10V~30V ±4.5V~20V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	145 ns
Max Dual Supply Voltage	20V
On-State Resistance (Max)	45Ohm
Min Dual Supply Voltage	4.5V
High Level Output Current	30mA
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	68 dB
Current - Leakage (IS(off)) (Max)	250pA
Channel Capacitance (CS(off), CD(off))	9pF 9pF
On-state Resistance Match-Nom	3Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	175ns, 145ns
Charge Injection	5pC
Channel-to-Channel Matching (ΔRon)	3 Ω (Max)
Crosstalk	-85dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	45Ohm
Normal Position	NO
Height	900μm
Length	5mm
Width	4.4mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free
Factory Lead Time	1 Week
Contact Plating	Tin
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Number of Pins	16
Weight	172.98879mg
Operating Temperature	0°C~70°C TA
Packaging	Tube
Published	2008
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)

DG412CUE+ Overview

As the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Extended operating temperature around 0°C~70°C TA. In total, there are 16 terminations. Due to its 4 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. It is part of the design of the 16 series that this electronic component is included. Circuits based on SPST - NO switching are used to construct these analog switch ics. Try searching for DG412 variants of the analog switch ic. There is 80Ohm internal resistance in this digital multiplexer. For functions related to 16 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. Digital switch that provides Dual, Single power at a cost-effective price. A low voltage of 10V should be applied to the electronic component. For this digital switch to work, 100pA current would suffice. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply. Drain to Source resistance is 45Ohm.