DG412DJ-E3

175ns, 145ns SPST - NO 35Ohm Analog Switches BREAK-BEFORE-MAKE DG412 16 Pins 250pA 15V 16-DIP (0.300, 7.62mm)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG412DJ-E3
Package: 16-DIP (0.300, 7.62mm)
Datasheet: PDF
Stock: 734
Description: 175ns, 145ns SPST - NO 35Ohm Analog Switches BREAK-BEFORE-MAKE DG412 16 Pins 250pA 15V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Through Hole
Mounting Type	Through Hole
Package / Case	16-DIP (0.300, 7.62mm)
Number of Pins	16
Weight	1.627801g
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2016
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	35Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	470mW
Technology	CMOS
Peak Reflow Temperature (Cel)	265
Number of Functions	4
Supply Voltage	15V
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG412
Output	SEPARATE OUTPUT
Pin Count	16
Operating Supply Voltage	15V
Number of Channels	1
Max Supply Voltage	36V
Min Supply Voltage	13V
Operating Supply Current	1μA
Nominal Supply Current	100pA
Power Dissipation	470mW
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	175 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	5V~44V ±5V~20V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	145 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	35Ohm
Min Dual Supply Voltage	7V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	68 dB
Current - Leakage (IS(off)) (Max)	250pA
Channel Capacitance (CS(off), CD(off))	9pF 9pF
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	175ns, 145ns
Charge Injection	5pC
Crosstalk	-85dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	220ns
Drain to Source Resistance	35Ohm
Normal Position	NO
Height	3.81mm
Length	21.33mm
Width	7.11mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG412DJ-E3 Overview

The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tube. This analog switch is mounted in Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. The operating temperature is extended to around -40°C~85°C TA. In total, there have been 16 terminations. High-quality output is provided by the electronic component's 1 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. Into the electrical component body are injected 16 pins. Based on SPST - NO switching circuits, these analog multiplexers work. Try searching with DG412 to find analog multiplexer variants. In this multiplexer, the internal resistance is 35Ohm. For details about the functions of 16 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. A voltage higher than 36V should not normally be supplied to the switches. Analogue multiplexers of the Dual, Single supply type that are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 13V. The switch device would be able to operate with 1μA current. When the digital multiplexer is charged above 1μA, damage can occur. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. It is recommended that you attach at least 7V to your dual power supply. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. 15V operating voltages are supported by the electronic component. There are 4 inputs to be operated. A Drain to Source resistance of 35Ohm is shown for this electronic part.