DG412DQ-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 80Ohm |
| Terminal Finish | PURE MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Number of Inputs | 4 |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 220ns |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±15V |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
DG412DQ-T1-E3 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, this analog switch is mounted. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 16. The electronic part delivers high-quality output through its 1 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. Electronic part bodies are injected with 16 pins. These analog multiplexers are built based on SPST - NO switching circuits. The internal resistance of this digital multiplexer is 80Ohm. You can find the functions of the 16 pins in the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. 13V is the lowest voltage the electrical component should receive. For this switch, a dual supply voltage is feasible, but it must not exceed 22VIf you are using a dual power supply, you should attach at least 7V. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. In order to operate the 4 inputs, there are several steps to follow.
DG412DQ-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO
DG412DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG412DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Avionics
- Avionics and Military Systems
- Relay replacements
- Medical Instrumentation
- T1/E1 Terminals
- Precision data acquisition
- DVD-R
- Isolation
- Avionics test equipment
- Remote wireless modules
