DG412DY
| Parameters | |
|---|---|
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Terminal Pitch | 1.27mm |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 30mA |
| Power Dissipation | 600mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 175 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 5V~44V ±5V~20V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Drain to Source Resistance | 25Ohm |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
DG412DY Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). To ensure high reliability, a new packaging method Tube is used. Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a ratio of 1:1. The operating temperature is extended to around -40°C~85°C TA. The total number of terminations is 16. There is an electrical component included in the 16 series. Multiplexers built on a SPST - NO switching circuit are built. The internal resistance of this digital multiplexer is 35Ohm. Datasheets for 16 pin functions are available upon request. There is a standard Multiplexer or Switches analogue multiplexer here. In normalcircumstances, users should not exceed 36V volts for the multiplexer. A cost-effective Dual, Single supply type analogue multiplexer. There should be 13V voltage fed to the electrical part below 13V. This digital switch can be operated with a current of 30mA. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. There is no problem with using dual supply voltage, but it should not exceed 22V. It is recommended that you attach at least 7V to your dual power supply. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. Operating 4 inputs is required. Drain to Source resistance is 25Ohm.
DG412DY Features
Switch Circuit: SPST - NO
30mA Supply Current
Drain-to-Source resistance: 25Ohm
DG412DY Applications
There are a lot of Vishay Siliconix DG412DY Analog Switches & Multiplexers ICs applications.
- E1 Network Equipment
- Data switching
- Avionics and Military Systems
- FTTH
- Digital access cross connects
- Video signal routing
- Sample-and-hold systems
- Precision data acquisition
- Mechanical reed relay replacement
- SONET/SDH ADM
