DG412DYZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Packaging | Bulk |
| Published | 1999 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Operating Supply Voltage | 28V |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 5μA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Off-state Isolation-Nom | 68 dB |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 175ns |
| Drain to Source Resistance | 35Ohm |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
DG412DYZ Overview
Packed in SOIC, the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Bulk. In total, 16 terminations have occurred. As a result of its 1 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. As far as internal resistance is concerned, it has 80Ohm. The functions of 16 pins can be found in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. In a normalsituation, users should not supply the switches with voltage higher than 40V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. The lowest voltage the electronic part should receive is 5V. The switch device would be able to operate with 100pA current. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. A dual power supply should have at least 5V voltage attached. Operating voltages of 28V are compatible with the electrical part. During operation, the multiplexer should not be exposed to a temperature above 85°C. Drain to Source resistance for this electronic component is 35Ohm. It is capable of carrying out 4-bit operation.
DG412DYZ Features
1 Channels
100pA Supply Current
Drain-to-Source resistance: 35Ohm
4-Bit
DG412DYZ Applications
There are a lot of Intersil (Renesas Electronics America) DG412DYZ Analog Switches & Multiplexers ICs applications.
- USB 1.1 signal switching circuits
- Fiber to the Home
- HDTV
- Wireless Local Loop
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Avionics test equipment
- Microprocessor Controlled Analog Systems
- Audio/video switches
- Low-Voltage
- Communications systems
