DG412FDY+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1994 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 85Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG412 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 355μA |
| Max Supply Current | 600μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 15pF 47pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -105dB @ 1MHz |
| Switch-on Time-Max | 175ns |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG412FDY+T Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. This analog switch is mounted in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. In total, 16 terminations have occurred. As a result of its 1 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. This electrical component is included in the 16 series of products. Multiplexers built on a SPST - NO switching circuit are built. There are 4 circuits in this multiplexer. If you are looking for variants of the digital switch, trying search with DG412. There is 85Ohm internal resistance in this digital multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. A cost-effective Dual, Single supply type analogue multiplexer. 9V is the lowest voltage the electrical component should receive. If you put voltage higher than 600μA on the digital multiplexer, damage may occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. The voltage should be at least 4.5V if you are using dual power supplies. 18V operating voltages are supported by the electronic component.
DG412FDY+T Features
1 Channels
Switch Circuit: SPST - NO
DG412FDY+T Applications
There are a lot of Maxim Integrated DG412FDY+T Analog Switches & Multiplexers ICs applications.
- Modems
- Microprocessor Controlled Analog Systems
- SONET
- Medical systems
- Digital access cross connects
- Sample-and-hold systems
- PBXs
- SDH
- Medical Instrumentation
- PBX interfaces
