DG412FEUE+
| Parameters | |
|---|---|
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 85Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 457mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG412 |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Number of Channels | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 600μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 220 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 15pF 47pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -105dB @ 1MHz |
| Switch-on Time-Max | 175ns |
| Height | 950μm |
| Length | 5.1mm |
| Width | 4.5mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2002 |
DG412FEUE+ Overview
As the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. Advanced packaging method Tube is used to provide high reliability. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 16. The electronic part delivers high-quality output through its 4 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. Electronic part bodies are injected with 16 pins. These analog multiplexers are built based on SPST - NO switching circuits. If you are looking for variants of the digital switch, trying search with DG412. There is 85Ohm internal resistance in this digital multiplexer. For functions related to 16 pins, please refer to the datasheets. A voltage higher than 36V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Dual, Single supply type. 9V is the lowest voltage the electrical component should receive. If put voltage greater than 600μA on the device, damage may be caused to the analogue multiplexer. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. With dual power supplies, you should attach at least 4.5V. There is a voltage range of 20V operating voltages for the electrical part.
DG412FEUE+ Features
4 Channels
Switch Circuit: SPST - NO
DG412FEUE+ Applications
There are a lot of Maxim Integrated DG412FEUE+ Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- PDH Multiplexers
- Video switching
- DVD-R
- RGB switches
- USB 1.1 signal switching circuits
- Cable PC
- Audio and video signal routing
- Frame Relay Equipment
- Cross Connects
