DG412FEUE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 85Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 755mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | DG412 |
| Pin Count | 16 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 355μA |
| Max Supply Current | 600μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 15pF 47pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -105dB @ 1MHz |
| Switch-on Time-Max | 175ns |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG412FEUE+T Overview
Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operational temperature extended around -40°C~85°C TA. In total, 16 terminations have occurred. As a result of its 1 channels, this electronic component provides high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. 16 pins are injected to the electronic part body. The analog switch ics are built using SPST - NO switching circuits. It consists of 4 circuits. DG412 can be used to search for analog multiplexer variants. A 85Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 16 pins functions. In a normalsituation, users should not supply the switches with voltage higher than 36V. Analog switch ics with Dual, Single supply type are cost-effective. A low voltage of 9V should be applied to the electronic component. Putting voltage greater than 600μA on the multiplexer may cause damage. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. The voltage should be at least 4.5V if you are using dual power supplies. There is a voltage range of 18V operating voltages for the electrical part.
DG412FEUE+T Features
1 Channels
Switch Circuit: SPST - NO
DG412FEUE+T Applications
There are a lot of Maxim Integrated DG412FEUE+T Analog Switches & Multiplexers ICs applications.
- Digital cross connects (DSX-1)
- Video signal routing
- Isolation
- Fiber to the Home
- Audio and video routing
- Avionics and Military Systems
- Residential Gateways, Home Gateway/Router
- SDH
- Audio/video switches
- Microprocessor controlled systems
