DG412HSDJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 35Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 105 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 105 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 91 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 105ns, 80ns |
| Charge Injection | 22pC |
| Crosstalk | -88dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 90ns |
| Normal Position | NO/NC |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| RoHS Status | Non-RoHS Compliant |
DG412HSDJ Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Tube. Through Hole is where this multiplexer is located. Multiplexers and demultiplexers have a number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. There are 16 terminations totally. A high-quality output is provided by the electrical component's 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. This electrical component is included in the 16 series of products. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Circuits number 4 make up this analogue multiplexer. A 35Ohm internal resistance characterizes this multiplexer. Datasheets for functions of 16 pins are available. There is a standard Multiplexer or Switches analogue multiplexer here. A voltage higher than 44V should not normally be supplied to the switches. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 13V. Put voltage above 1μA on the multiplexer to cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. A dual power supply should have at least 7V voltage attached. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
DG412HSDJ Features
1 Channels
Switch Circuit: SPST - NO
DG412HSDJ Applications
There are a lot of Vishay Siliconix DG412HSDJ Analog Switches & Multiplexers ICs applications.
- Automotive applications
- ATM
- PCMCIA cards
- Sample-and-hold systems
- Access Concentrators
- PBX interfaces
- SDH
- Industrial
- Channel Banks
- Precision test equipment
