DG412HSDJ-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 80Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | DG412 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 105 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 105 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 91 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 105ns, 80ns |
| Charge Injection | 22pC |
| Crosstalk | -88dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 90ns |
| Normal Position | NO |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG412HSDJ-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). This packaging method provides high reliability because it uses advanced packaging techniques. Mounted in Through Hole is this multiplexer. Multiplexer and demultiplexer circuits have a number 1:1. Extended operating temperature around -40°C~85°C TA. Total terminations are 16. A high-quality output is provided by the electrical component's 1 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. As part of its design, the 16 series is equipped with this electronic component. Based on SPST - NO switching circuits, these analog multiplexers work. There are 4 circuits in this multiplexer. Try searching for DG412 variants of the analog switch ic. As far as internal resistance is concerned, it has 80Ohm. Datasheets for functions of 16 pins are available. A analogue multiplexer of this type is a Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 44V. Dual, Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 13V. For this digital switch to work, 1μA current would suffice. The analogue multiplexer may be damaged if voltage is greater than 1μA. Despite this switch device's dual supply capability, its voltage should not exceed 22V. For dual power supplies, a voltage of at least 7V should be attached. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
DG412HSDJ-E3 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
DG412HSDJ-E3 Applications
There are a lot of Vishay Siliconix DG412HSDJ-E3 Analog Switches & Multiplexers ICs applications.
- RGB switches
- MP3 players
- Industrial
- Medical Instrumentation
- Avionics
- Industrial and process control systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Switching Systems
- Public switching systems
- Digital access cross connects
