Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-VQFN Exposed Pad |
Number of Pins |
16 |
Weight |
57.09594mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2016 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
80Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
1.88W |
Technology |
CMOS |
Terminal Position |
QUAD |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG412 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Number of Channels |
1 |
Max Supply Voltage |
44V |
Min Supply Voltage |
13V |
Operating Supply Current |
1μA |
Power Dissipation |
1.88W |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
105 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
12V ±5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
105 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
91 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 12pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
105ns, 80ns |
Charge Injection |
22pC |
Crosstalk |
-88dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
90ns |
Normal Position |
NO |
Height |
950μm |
Length |
4mm |
Width |
4mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
DG412HSDN-T1-E4 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-VQFN Exposed Pad. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. Total terminations are 16. By its 1 channels, the electronic component provides high-quality output. A 15V voltage supply should turn on and run the electronic component. It is part of the design of the 16 series that this electronic component is included. Multiplexers built on a SPST - NO switching circuit are built. DG412 can be used to search for analog multiplexer variants. There is 80Ohm internal resistance in this digital multiplexer. For details about the functions of 16 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. A voltage higher than 44V should not normally be supplied to the switches. Analog switch ics with Dual, Single supply type are cost-effective. The lowest voltage fed to the electronic component should be 13V. The analogue multiplexer could operate on 1μA current. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. With dual power supplies, you should attach at least 7V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. Operating the 4 inputs requires 4 inputs.
DG412HSDN-T1-E4 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
DG412HSDN-T1-E4 Applications
There are a lot of Vishay Siliconix DG412HSDN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Multi-Line E1 Interface Cards
- Cell phones
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Routers
- Microprocessor controlled systems
- Industrial control systems
- Microprocessor Controlled Analog Systems
- Public switching systems
- MP3 players
- Precision test equipment