Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
547.485991mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2013 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
35Ohm |
Terminal Finish |
TIN LEAD |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
600mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
30 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Max Supply Voltage |
44V |
Min Supply Voltage |
13V |
Power Dissipation |
600mW |
Max Supply Current |
1μA |
Turn On Delay Time |
105 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
12V ±5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
105 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
91 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 12pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
105ns, 80ns |
Charge Injection |
22pC |
Crosstalk |
-88dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
90ns |
Drain to Source Resistance |
25Ohm |
Normal Position |
NO/NC |
Height |
1.55mm |
Length |
10mm |
Width |
4mm |
RoHS Status |
Non-RoHS Compliant |
DG412HSDY Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. This analog switch is mounted in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~85°C TA extended. Total terminations are 16. A high-quality output is provided by the electrical component's 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. This electronic part can be found in the 16 series. SPST - NO switching circuits are used in these analog switch ics. This digital multiplexer has 35Ohm internal resistance. To find out what the functions of 16 pins are, please refer to their datasheets. In this analog multiplexer, the value is Multiplexer or Switches. A voltage higher than 44V should not normally be supplied to the switches. Digital switch that provides Dual, Single power at a cost-effective price. A low voltage of 13V should be applied to the electronic component. Putting voltage greater than 1μA on the multiplexer may cause damage. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. If you are using dual power supplies, you should attach at least 7V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. The 4 inputs need to be operated in order to work. A Drain to Source resistance of 25Ohm is shown for this electronic part.
DG412HSDY Features
1 Channels
Switch Circuit: SPST - NO
Drain-to-Source resistance: 25Ohm
DG412HSDY Applications
There are a lot of Vishay Siliconix DG412HSDY Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- Communication systems
- Mechanical reed relay replacement
- Private Branch Exchange (PBX)
- New designs requiring multiplexer functions
- Channel Banks
- CSU
- SONET/SDH ADM
- Sample hold systems
- Industrial and process control systems