DG412HSDY-T1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 547.485991mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 35Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Power Dissipation | 600mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 105 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 105 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 91 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 105ns, 80ns |
| Charge Injection | 22pC |
| Crosstalk | -88dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 90ns |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG412HSDY-T1 Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 1:1. Operating temperature extended to -40°C~85°C TA. There are 16 terminations totally. The electronic part delivers high-quality output through its 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. This electrical component is included in the 16 series of products. Unlike digital switches, these are based on SPST - NO switching circuits. A 35Ohm internal resistance characterizes this multiplexer. Datasheets for functions of 16 pins are available. This switch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 44V to the switch device in normal circumstances. The analog switch ic is of the Dual, Single supply type and is cost-effective. 13V is the lowest voltage the electrical component should receive. Put voltage above 1μA on the multiplexer to cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. For dual power supplies, a voltage of at least 7V should be attached. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. Operating the 4 inputs requires 4 inputs.
DG412HSDY-T1 Features
1 Channels
Switch Circuit: SPST - NO
DG412HSDY-T1 Applications
There are a lot of Vishay Siliconix DG412HSDY-T1 Analog Switches & Multiplexers ICs applications.
- Optical Applications
- High-Voltage
- Fiber to the Home
- Data Acquisition Systems
- RGB switches
- DVD-R
- Cable Modem
- PDAs
- Automatic test equipment
- Relay replacements
