DG412LDQ
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 17Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Terminal Pitch | 0.635mm |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 3/12/+-5V |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 50 ns |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 35 ns |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 280MHz |
| On-State Resistance (Max) | 17Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 19ns, 12ns |
| Charge Injection | 5pC |
| Crosstalk | -95dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 85ns |
| Normal Position | NO |
| Height | 920μm |
| Length | 5.08mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG412LDQ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). High reliability is provided by advanced packaging method Tube. In Surface Mount, this analog switch is mounted. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. Total terminations are 16. There are 16 pins injected into the electronic part body. Multiplexers built on a SPST - NO switching circuit are built. The multiplexer consists of 4 circuits. In this multiplexer, the internal resistance is 17Ohm. Datasheets for 16 pin functions are available upon request. There is a standard Multiplexer or Switches analogue multiplexer here. In a normalsituation, users should not supply the switches with voltage higher than 12V. Dual, Single supply type digital switch with a low cost. It is recommended that the electrical component receives a voltage of 2.7V. A voltage higher than 1μA may cause damage to the switch multiplexer. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 6V. With dual power supplies, you should attach at least 3V. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
DG412LDQ Features
Switch Circuit: SPST - NO
-3db Bandwidth: 280MHz
DG412LDQ Applications
There are a lot of Vishay Siliconix DG412LDQ Analog Switches & Multiplexers ICs applications.
- RGB switches
- Modems
- Battery Powered Instruments
- Sample-and-hold systems
- PBXs
- Data switching
- SDH/SONET multiplexers
- High-Voltage
- Intelligent PBX
- Multi-Line E1 Interface Cards
