DG412LDQ-E3

19ns, 12ns SPST - NO 17Ohm Analog Switches BREAK-BEFORE-MAKE DG412 16 Pins 250pA 5V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG412LDQ-E3
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 174
Description: 19ns, 12ns SPST - NO 17Ohm Analog Switches BREAK-BEFORE-MAKE DG412 16 Pins 250pA 5V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Channel Capacitance (CS(off), CD(off))	5pF 6pF
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	19ns, 12ns
Charge Injection	5pC
Crosstalk	-95dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	60ns
Normal Position	NO
Height	920μm
Length	5.08mm
Width	4.4mm
RoHS Status	ROHS3 Compliant
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Number of Pins	16
Weight	172.98879mg
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2017
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	50Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	450mW
Technology	BICMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	5V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG412
Output	SEPARATE OUTPUT
Pin Count	16
Qualification Status	Not Qualified
Power Supplies	3/12/+-5V
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	12V
Min Supply Voltage	2.7V
Operating Supply Current	1μA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	50 ns
Voltage - Supply, Single/Dual (±)	2.7V~12V ±3V~6V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	35 ns
Max Dual Supply Voltage	6V
-3db Bandwidth	280MHz
On-State Resistance (Max)	17Ohm
Min Dual Supply Voltage	3V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	68 dB
Current - Leakage (IS(off)) (Max)	250pA

DG412LDQ-E3 Overview

Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Increasing operating temperature to around -40°C~85°C TA. The total number of terminations is 16. High-quality output is provided by the electronic component's 1 channels. When the electronic component is given a voltage of 5V, it should be turned on and run. 16 pins are injected to the electronic part body. The analog switch ics are built using SPST - NO switching circuits. Circuits number 4 make up this analogue multiplexer. Search with DG412 if you are looking for analog multiplexer variants. Analog switches have 50Ohm internal resistance. Please refer to the datasheets for 16 pins functions. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 12V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. A low voltage of 2.7V should be applied to the electronic component. In order to operate this switch device, it would need a current of 1μA. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 6V. In the case of dual power supplies, you should connect at least 3V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.