Parameters |
Max Power Dissipation |
650mW |
Technology |
BICMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
4 |
Supply Voltage |
5V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Power Supplies |
3/12/+-5V |
Number of Channels |
1 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2.7V |
Power Dissipation |
650mW |
Max Supply Current |
1μA |
Turn On Delay Time |
50 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
2.7V~12V ±3V~6V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
35 ns |
Max Dual Supply Voltage |
6V |
-3db Bandwidth |
280MHz |
On-State Resistance (Max) |
17Ohm |
Min Dual Supply Voltage |
3V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
5pF 6pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
19ns, 12ns |
Charge Injection |
5pC |
Crosstalk |
-95dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
60ns |
Normal Position |
NO |
Height |
1.55mm |
Length |
10mm |
Width |
4mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
547.485991mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2012 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
17Ohm |
Terminal Finish |
TIN LEAD |
Subcategory |
Multiplexer or Switches |
DG412LDY-T1 Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. High reliability is ensured by the advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operating temperature extended to -40°C~85°C TA. In total, 16 terminations have occurred. The electronic part provides high-quality output because it has 1 channels. It is safe to turn on and run the electronic component with a 5V voltage supply. This electronic part can be found in the 16 series. Based on SPST - NO switching circuits, these analog multiplexers work. An switch multiplexer with 17Ohm internal resistance has a value of 17Ohm. The datasheets for the 16 pins explain the functions. There is Multiplexer or Switches analog multiplexer like this in the world. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. An effective Dual, Single supply digital multiplexer. It is recommended that the electrical component receives a voltage of 2.7V. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 6V. In the case of dual power supplies, you should connect at least 3V. There are SEPARATE OUTPUT outputs on this analog switch ic. Operating the 4 inputs requires 4 inputs.
DG412LDY-T1 Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 280MHz
DG412LDY-T1 Applications
There are a lot of Vishay Siliconix DG412LDY-T1 Analog Switches & Multiplexers ICs applications.
- RGB switches
- Video signal routing
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Intelligent PBX
- Medical systems
- Routers
- Avionics
- Remote Powered Equipment
- Multi-Line E1 Interface Cards
- DSLAMs