Parameters |
Factory Lead Time |
1 Week |
Mounting Type |
Through Hole |
Package / Case |
16-CDIP (0.300, 7.62mm) |
Surface Mount |
NO |
Number of Pins |
16 |
Operating Temperature |
-55°C~125°C TA |
Packaging |
Tube |
Published |
1994 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
30Ohm |
Terminal Finish |
Tin/Lead (Sn/Pb) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
800mW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
245 |
Number of Functions |
4 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
20 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
28V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
30V |
Min Supply Voltage |
10V |
Max Supply Current |
1μA |
Turn On Delay Time |
250 ns |
Voltage - Supply, Single/Dual (±) |
10V~30V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
145 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
30Ohm |
Min Dual Supply Voltage |
4.5V |
Screening Level |
MIL-STD-883 Class B |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
On-state Resistance Match-Nom |
3Ohm |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
175ns, 145ns |
Charge Injection |
5pC |
Channel-to-Channel Matching (ΔRon) |
3 Ω (Max) |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
175ns |
Height Seated (Max) |
5.08mm |
Width |
7.62mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
DG413AK/883B Overview
The electrical component comes in 16-CDIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Tube. In Through Hole, you'll find this switch device. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Increasing operating temperature to around -55°C~125°C TA. The total number of terminations is 16. The electronic part provides high-quality output because it has 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. This electrical component is included in the 16 series of products. On the other hand, analog switches can be constructed using SPST - NO/NC switching circuits. It consists of 4 circuits. There is 30Ohm internal resistance in this digital multiplexer. The functions of 16 pins can be found in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 30V. A cost-effective Dual, Single supply type analogue multiplexer. It is recommended to use 10V as the lowest voltage for the electrical part. A voltage higher than 1μA may cause damage to the switch multiplexer. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. A dual power supply should have at least 4.5V voltage attached. There are SEPARATE OUTPUT outputs on this analog switch ic. 28V operating voltages are supported by the electronic component.
DG413AK/883B Features
1 Channels
Switch Circuit: SPST - NO/NC
DG413AK/883B Applications
There are a lot of Maxim Integrated DG413AK/883B Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- Medical systems
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Data Acquisition Systems
- Communication systems
- Precision data acquisition
- Access Concentrators
- Routers
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Microwave transmission systems