banner_page

DG413DVZ-T

Analog Switches BREAK-BEFORE-MAKE 15V TSSOP


  • Manufacturer: Intersil (Renesas Electronics America)
  • Nocochips NO: 391-DG413DVZ-T
  • Package: TSSOP
  • Datasheet: PDF
  • Stock: 729
  • Description: Analog Switches BREAK-BEFORE-MAKE 15V TSSOP(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Package / Case TSSOP
Number of Pins 16
Published 1999
JESD-609 Code e3
Part Status Active
Moisture Sensitivity Level (MSL) 1
Number of Terminations 16
Resistance 80Ohm
Terminal Finish Matte Tin (Sn) - annealed
Max Operating Temperature 85°C
Min Operating Temperature -40°C
HTS Code 8542.39.00.01
Subcategory Multiplexer or Switches
Technology CMOS
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 4
Supply Voltage 15V
Terminal Pitch 0.65mm
Time@Peak Reflow Temperature-Max (s) 30
Output SEPARATE OUTPUT
Operating Supply Voltage 28V
Temperature Grade INDUSTRIAL
Number of Channels 1
Max Supply Voltage 40V
Min Supply Voltage 5V
Operating Supply Current 100pA
Nominal Supply Current 100pA
Max Supply Current 1μA
Throw Configuration SPST
Turn On Delay Time 250 ns
Supply Type Dual, Single
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 145 ns
Max Dual Supply Voltage 20V
Min Dual Supply Voltage 5V
Dual Supply Voltage 18V
Off-state Isolation-Nom 68 dB
Switching BREAK-BEFORE-MAKE
Switch-on Time-Max 175ns
Height Seated (Max) 1.2mm
Length 5mm
Width 4.4mm
Radiation Hardening No
RoHS Status RoHS Compliant

DG413DVZ-T Overview


This electronic part is conveniently packaged in TSSOP, making it easy to ship abroad. In total, there have been 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 15V voltage supply. In this multiplexer, the internal resistance is 80Ohm. The functions of 16 pins can be found in the datasheets. Multiplexer or Switches is a typical switch device. Multiplexers should not be powered above 40V in normal situations. An effective Dual, Single supply digital multiplexer. 5V should be the lowest voltage fed to the electronic component. For this multiplexer to operate, 100pA current would be sufficient. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. If you are using dual power supplies, you should attach at least 5V. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. 28V operating voltages are supported by the electronic component. Temperatures over 85°C should not be allowed for the multiplexer to operate.

DG413DVZ-T Features


1 Channels
100pA Supply Current

DG413DVZ-T Applications


There are a lot of Intersil (Renesas Electronics America) DG413DVZ-T Analog Switches & Multiplexers ICs applications.

  • Cellular phones
  • PDAs
  • ATM
  • Power routing
  • Fault Tolerant Systems
  • Voice over IP/DSL – Integrated Access Devices, Smart
  • ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
  • Central office
  • Cable Modem
  • Relay replacements

Write a review

Note: HTML is not translated!
    Bad           Good