DG413DY+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG413 |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Polarity | Non-Inverting |
| Power Supplies | 512/+-15V |
| Number of Channels | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 100pA |
| Max Supply Current | 100pA |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 9V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG413DY+ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Operational temperature extended around -40°C~85°C TA. There are 16 terminations totally. A 4 channel electronic part produces high-quality output. Turning on and running the electrical part should be easy with a 15V voltage supply. Electronic part bodies are injected with 16 pins. The analog switch ics are built using SPST - NO/NC switching circuits. DG413 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 80Ohm. Datasheets for functions of 16 pins are available. Multiplexer or Switches is a typical switch device. A voltage higher than 30V should not normally be supplied to the switches. An effective Dual, Single supply digital multiplexer. There should be 10V voltage fed to the electrical part below 10V. This digital switch can be operated with a current of 100pA. If you put voltage higher than 100pA on the digital multiplexer, damage may occur. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply. Operating voltages range from 20V.
DG413DY+ Features
4 Channels
Switch Circuit: SPST - NO/NC
100pA Supply Current
DG413DY+ Applications
There are a lot of Maxim Integrated DG413DY+ Analog Switches & Multiplexers ICs applications.
- SONET/SDH ADM
- PBXs
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- DSLAMs
- Access Concentrators
- Frame Relay Equipment
- Video signal routing
- Mechanical reed relay replacement
- Signal routing between systems
- Microprocessor controlled systems
