DG413DY
| Parameters | |
|---|---|
| Max Supply Current | 1μA |
| Turn On Delay Time | 175 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 5V~44V ±5V~20V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Drain to Source Resistance | 35Ohm |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2014 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Terminal Pitch | 1.27mm |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 30mA |
| Power Dissipation | 600mW |
DG413DY Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. Advanced packaging method Tube is used to provide high reliability. Mounted in Surface Mount is this multiplexer. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around -40°C~85°C TA. 16 terminations have been made so far. Into the electrical component body are injected 16 pins. A SPST - NO/NC switching circuit is used to build these analog multiplexers. This digital multiplexer has 35Ohm internal resistance. To find out what the functions of 16 pins are, please refer to their datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 36V. A cost-effective Dual, Single supply type analogue multiplexer. It is recommended to use 13V as the lowest voltage for the electrical part. 30mA current would be enough for this multiplexer to operate. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. There is no problem with using dual supply voltage, but it should not exceed 22V. You should attach at least 7V voltage if you are using dual power supply. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. There are 4 inputs to be operated. It has a Drain to Source resistance of 35Ohm ohms.
DG413DY Features
Switch Circuit: SPST - NO/NC
30mA Supply Current
Drain-to-Source resistance: 35Ohm
DG413DY Applications
There are a lot of Vishay Siliconix DG413DY Analog Switches & Multiplexers ICs applications.
- Video signal routing
- Relay replacements
- Mechanical reed relay replacement
- 65 V DACs
- Precision instrumentation
- Multi-Line E1 Interface Cards
- Multiplexers
- Cable Modem
- Microprocessor controlled systems
- Fiber to the Home
