DG413DYZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Packaging | Bulk |
| Published | 1999 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 100pA |
| Max Supply Current | 5μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 315 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 140 ns |
| Max Dual Supply Voltage | 20V |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 15V |
| Off-state Isolation-Nom | 68 dB |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 175ns |
| Drain to Source Resistance | 25mOhm |
| Height | 1.75mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
DG413DYZ Overview
The electronic part can be shipped overseas conveniently because it is packaged in SOIC. This packaging method provides high reliability because it uses advanced packaging techniques. A total of 16 terminations have been recorded. Due to its 1 channels, the electrical component produces high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. Internally, this switch multiplexer has a resistance of 35Ohm. You can find the functions of the 16 pins in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 40V in normal situations. An effective Dual, Single supply digital multiplexer. It is recommended to use 5V as the lowest voltage for the electrical part. The analogue multiplexer could operate on 100pA current. Put voltage above 5μA on the multiplexer to cause damage. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. When using dual power supplies, you should attach at least 5V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. The 4 inputs need to be operated in order to work. Temperatures above 85°C degrees Celsius should not be operated by the multiplexer. A Drain to Source resistance of 25mOhm is shown for this electronic part.
DG413DYZ Features
1 Channels
100pA Supply Current
Drain-to-Source resistance: 25mOhm
DG413DYZ Applications
There are a lot of Intersil (Renesas Electronics America) DG413DYZ Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- DSUs
- Access Concentrators
- Cellular phones
- HDTV
- Optical Applications
- Remote Powered Equipment
- Frame Relay Equipment
- Wireless Local Loop
- E1 Multiplexer
