DG413FEUE+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1994 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 85Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 755mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG413 |
| Pin Count | 16 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 355μA |
| Max Supply Current | 600μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 15pF 47pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -105dB @ 1MHz |
| Switch-on Time-Max | 175ns |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG413FEUE+T Overview
Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Surface Mount is where this multiplexer is located. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature around -40°C~85°C TA extended. In total, there are 16 terminations. High-quality output is provided by the electronic component's 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. A SPST - NO/NC switching circuit is used for these analog switches. There are 4 circuits in this switch device. Try searching with DG413 if you're looking for variants. The internal resistance of this digital multiplexer is 85Ohm. You can find the functions of the 16 pins in the datasheets. In normalcircumstances, users should not exceed 36V volts for the multiplexer. A cost-effective Dual, Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 9V. It may damage the digital multiplexer if the voltage is higher than 600μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. When using dual power supplies, you should attach at least 4.5V. 18V operating voltages are supported by the electronic component.
DG413FEUE+T Features
1 Channels
Switch Circuit: SPST - NO/NC
DG413FEUE+T Applications
There are a lot of Maxim Integrated DG413FEUE+T Analog Switches & Multiplexers ICs applications.
- Optical Applications
- E1 Network Equipment
- Audio signal routing
- Video switching
- SDH
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Microprocessor controlled systems
- Mechanical reed relay replacement
- PBXs
- Battery Powered Systems
