DG413HSDJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 35Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 105 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 105 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 91 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 105ns, 80ns |
| Charge Injection | 22pC |
| Crosstalk | -88dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 90ns |
| Drain to Source Resistance | 25Ohm |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG413HSDJ Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tube. There is an analog multiplexer mounted in position Through Hole. Multiplexers and demultiplexers have a number of circuits 1:1. Operating temperature around -40°C~85°C TA extended. In total, there have been 16 terminations. The electronic part provides high-quality output because it has 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. The electronic part body is injected with 16 pins. Multiplexers built on a SPST - NO/NC switching circuit are built. A 4 circuit is present in this switch device. Internally, this switch multiplexer has a resistance of 35Ohm. For details about the functions of 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 44V. Analog switch ics with Dual, Single supply type are cost-effective. It is recommended to use 13V as the lowest voltage for the electrical part. It may damage the digital multiplexer if the voltage is higher than 1μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. The voltage should be at least 7V if you are using dual power supplies. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. Drain to Source resistance for this electronic component is 25Ohm.
DG413HSDJ Features
1 Channels
Switch Circuit: SPST - NO/NC
Drain-to-Source resistance: 25Ohm
DG413HSDJ Applications
There are a lot of Vishay Siliconix DG413HSDJ Analog Switches & Multiplexers ICs applications.
- Cellular phones
- ATM
- Fiber to the Home
- Low-Voltage
- Frame Relay Equipment
- Cable Modem
- 65 V DACs
- Optical Applications
- Wireless Local Loop
- Battery-powered systems
