DG413HSDJ-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 80Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | DG413 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 105 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 105 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 91 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 105ns, 80ns |
| Charge Injection | 22pC |
| Crosstalk | -88dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 90ns |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG413HSDJ-E3 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-DIP (0.300, 7.62mm). A high level of reliability can be achieved through the use of an advanced packaging method Tube. The multiplexer is located in Through Hole. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~85°C TA extended. The total number of terminations is 16. High-quality output is provided by the electronic component's 1 channels. Turning on and running the electrical part should be easy with a 15V voltage supply. A key feature of the 16 series is the inclusion of this electronic part as part of its design. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. There are 4 circuits in this multiplexer. Try searching for DG413 variants of the analog switch ic. This digital multiplexer has 80Ohm internal resistance. You can find the functions of the 16 pins in the datasheets. This switch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 44V volts for the multiplexer. Dual, Single supply type digital switch with a low cost. There should be 13V voltage fed to the electrical part below 13V. 1μA current would be enough for this multiplexer to operate. A voltage higher than 1μA may cause damage to the switch multiplexer. Despite this switch's dual supply capability, its voltage should not exceed 22V. With dual power supplies, you should attach at least 7V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
DG413HSDJ-E3 Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
DG413HSDJ-E3 Applications
There are a lot of Vishay Siliconix DG413HSDJ-E3 Analog Switches & Multiplexers ICs applications.
- Audio signal routing
- PDAs
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Power routing
- ISDN NT1/TA
- Battery Powered Instruments
- Fiber In The Loop (FITL)
- Optical Applications
- E1 Network Equipment
- HDTV
