DG413HSDN-T1-E4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-VQFN Exposed Pad |
| Number of Pins | 16 |
| Weight | 57.09594mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 80Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.88W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG413 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1μA |
| Power Dissipation | 1.88W |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 105 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 105 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 91 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 105ns, 80ns |
| Charge Injection | 22pC |
| Crosstalk | -88dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 90ns |
| Height | 950μm |
| Length | 4mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
DG413HSDN-T1-E4 Overview
As the electronic part is packed in 16-VQFN Exposed Pad, international shipping is convenient. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~85°C TA. In total, 16 terminations have occurred. As a result of its 1 channels, this electronic component provides high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. Into the electrical component body are injected 16 pins. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. Using the DG413 search parameter, you can discover variants of the switch. The internal resistance of this digital multiplexer is 80Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users should never supply a voltage higher than 44V to a switch device. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 13V is the lowest voltage that should be fed to the electronic electronic part. For this digital switch to work, 1μA current would suffice. A voltage higher than 1μA may cause damage to the switch multiplexer. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. A dual power supply should have at least 7V voltage attached. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. The 4 inputs need to be operated in order to work.
DG413HSDN-T1-E4 Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
DG413HSDN-T1-E4 Applications
There are a lot of Vishay Siliconix DG413HSDN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Data switching
- PDAs
- Medical
- Imaging
- CSU
- Relay replacements
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Remote Powered Equipment
- Cable Modem
- E1 Network Equipment
