DG413HSDY
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 547.485991mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 35Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Power Dissipation | 600mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 105 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 105 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 91 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 105ns, 80ns |
| Charge Injection | 22pC |
| Crosstalk | -88dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 90ns |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG413HSDY Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). In order to provide high reliability, an advanced packaging method Tube is used. It is mounted in the position Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Temperatures around -40°C~85°C TA are extended for operation. Totally, there are 16 terminations. A electrical component with 1 channels is capable of high-quality output. Turning on and running the electrical part should be easy with a 15V voltage supply. It is injected into the electrical part body with 16 pins. Based on SPST - NO/NC switching circuits, these analog multiplexers work. Internally, this switch multiplexer has a resistance of 35Ohm. For functions related to 16 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. In normalcircumstances, users should not exceed 44V volts for the multiplexer. Analogue multiplexer with a Dual, Single supply type that is cost-effective. There should be 13V voltage fed to the electrical part below 13V. It may damage the digital multiplexer if the voltage is higher than 1μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. For dual power supplies, a voltage of at least 7V should be attached. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. In order to operate the 4 inputs, there are several steps to follow.
DG413HSDY Features
1 Channels
Switch Circuit: SPST - NO/NC
DG413HSDY Applications
There are a lot of Vishay Siliconix DG413HSDY Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- Isolation
- RGB switches
- Battery Powered Systems
- FTTH
- Ultrasound
- Signal routing between systems
- Optical Applications
- Cable Modem
- ATM
