Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
665.986997mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
80Ohm |
Terminal Finish |
MATTE TIN |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
600mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG413 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
15V |
Number of Channels |
1 |
Max Supply Voltage |
44V |
Min Supply Voltage |
13V |
Operating Supply Current |
1μA |
Power Dissipation |
600mW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
105 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
12V ±5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
105 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
91 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 12pF |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
105ns, 80ns |
Charge Injection |
22pC |
Crosstalk |
-88dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
90ns |
Height |
1.55mm |
Length |
10mm |
Width |
4mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
DG413HSDY-E3 Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 16. A high-quality output is provided by the electrical component's 1 channels. A 15V voltage supply should turn on and run the electronic component. There are 16 pins injected into the electronic part body. A SPST - NO/NC switching circuit is used for these analog switches. Use DG413 to search for variants of the digital switches. As far as internal resistance is concerned, it has 80Ohm. The datasheets for the 16 pins explain the functions. A analogue multiplexer of this type is a Multiplexer or Switches. Users should never supply a voltage higher than 44V to a switch device. The digital multiplexer has a low cost Dual, Single supply. 13V is the lowest voltage that should be fed to the electronic electronic part. For this digital switch to work, 1μA current would suffice. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. For this switch, a dual supply voltage is feasible, but it must not exceed 22VThe voltage should be at least 7V if you are using dual power supplies. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. 15V operating voltages can be used with this electrical part. In order to operate the 4 inputs, there are several steps to follow.
DG413HSDY-E3 Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
DG413HSDY-E3 Applications
There are a lot of Vishay Siliconix DG413HSDY-E3 Analog Switches & Multiplexers ICs applications.
- Cellular phones
- Cable Modem
- Medical Instrumentation
- DVD-R
- Residential Gateways, Home Gateway/Router
- Frame Relay Equipment
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Modems
- Digital Cross-Connects