Parameters |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
30 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
JESD-30 Code |
R-PDSO-G16 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
44V |
Min Supply Voltage |
13V |
Max Supply Current |
1μA |
Turn On Delay Time |
105 ns |
Voltage - Supply, Single/Dual (±) |
12V ±5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
105 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
91 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 12pF |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
105ns, 80ns |
Charge Injection |
22pC |
Crosstalk |
-88dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
116ns |
Switch-off Time-Max |
90ns |
Height |
1.55mm |
Length |
10mm |
Width |
4mm |
RoHS Status |
Non-RoHS Compliant |
Factory Lead Time |
1 Week |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Weight |
547.485991mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2016 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
35Ohm |
Terminal Finish |
TIN LEAD |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
600mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
DG413HSDY-T1 Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. The operating temperature is extended to around -40°C~85°C TA. In total, there have been 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. A 15V voltage supply should turn on and run the electronic component. As part of the design of the 16 series, this electronic part has been incorporated into the system. On the other hand, analog switches can be constructed using SPST - NO/NC switching circuits. The circuits in this analogue multiplexer number 4. In this multiplexer, the internal resistance is 35Ohm. This switch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 44V volts for the multiplexer. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 13V is the lowest voltage that should be fed to the electronic electronic part. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. For dual power supplies, a voltage of at least 7V should be attached. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
DG413HSDY-T1 Features
1 Channels
Switch Circuit: SPST - NO/NC
DG413HSDY-T1 Applications
There are a lot of Vishay Siliconix DG413HSDY-T1 Analog Switches & Multiplexers ICs applications.
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Signal routing between systems
- Transmit
- Audio/video switches
- Microprocessor controlled systems
- T1/E1 Terminals
- SDH/SONET multiplexers
- Video switching
- Digital access cross connects
- SDH