DG413LDQ-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Bulk |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 50Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG413 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 20nA |
| Power Dissipation | 450mW |
| Throw Configuration | SPST |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 280MHz |
| On-State Resistance (Max) | 17Ohm |
| Min Dual Supply Voltage | 3V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 19ns, 12ns |
| Charge Injection | 5pC |
| Crosstalk | -95dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 60ns |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG413LDQ-E3 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). High reliability is provided by advanced packaging method Bulk. The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 16. By its 1 channels, the electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 5V voltage supply. The electronic part body is injected with 16 pins. A SPST - NO/NC switching circuit is used to build these analog multiplexers. Look for analog switch ic variants by searching with DG413. In this multiplexer, the internal resistance is 50Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. The digital multiplexer has a low cost Dual, Single supply. There should be 2.7V voltage fed to the electrical part below 2.7V. This digital switch can be operated with a current of 1μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 6V. When using dual power supplies, you should attach at least 3V. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. In order to operate the 4 inputs, there are several steps to follow.
DG413LDQ-E3 Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
-3db Bandwidth: 280MHz
DG413LDQ-E3 Applications
There are a lot of Vishay Siliconix DG413LDQ-E3 Analog Switches & Multiplexers ICs applications.
- Video signal routing
- Data Acquisition Systems
- Digital Cross-Connects
- HDTV
- Access Concentrators
- Communications systems
- Sample-and-hold systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- ATM
- PDAs
