DG413LDQ-T1
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 17Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 3/12/+-5V |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Power Dissipation | 450mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 50 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 35 ns |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 280MHz |
| On-State Resistance (Max) | 17Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 19ns, 12ns |
| Charge Injection | 5pC |
| Crosstalk | -95dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 60ns |
| Height | 920μm |
| Length | 5.08mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG413LDQ-T1 Overview
Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. In Surface Mount, this analog switch is mounted. 1:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. In total, there have been 16 terminations. The electronic part delivers high-quality output through its 1 channels. It is safe to turn on and run the electronic component with a 5V voltage supply. The electronic part body is injected with 16 pins. Unlike digital switches, these are based on SPST - NO/NC switching circuits. Internally, this switch multiplexer has a resistance of 17Ohm. To find out what the 16 pins do, please refer to the datasheets. Multiplexer or Switches is a typical switch device. A voltage higher than 12V should not normally be supplied to the switches. The digital multiplexer has a low cost Dual, Single supply. The lowest voltage the electronic part should receive is 2.7V. The analogue multiplexer may be damaged if voltage is greater than 1μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 6V. If you are using dual power supplies, you should attach at least 3V. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. The 4 inputs need to be operated in order to work.
DG413LDQ-T1 Features
1 Channels
Switch Circuit: SPST - NO/NC
-3db Bandwidth: 280MHz
DG413LDQ-T1 Applications
There are a lot of Vishay Siliconix DG413LDQ-T1 Analog Switches & Multiplexers ICs applications.
- Intelligent PBX
- Avionics test equipment
- Relay replacements
- Power routing
- Battery Powered Instruments
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Microprocessor controlled systems
- Isolation
- PBXs
- PDH Multiplexers
