DG413LDQ-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Supplier Device Package | 16-TSSOP |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 50Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 450mW |
| Base Part Number | DG413 |
| Number of Outputs | 4 |
| Number of Channels | 4 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Power Dissipation | 450mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 50 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 35 ns |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 280MHz |
| On-State Resistance (Max) | 17Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 19ns, 12ns |
| Charge Injection | 5pC |
| Crosstalk | -95dB @ 1MHz |
| Height | 920μm |
| Length | 5.08mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG413LDQ-T1-E3 Overview
Due to its 16-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. Multiplexer and demultiplexer circuits have a number 1:1. Increasing operating temperature to around -40°C~85°C TA. Due to its 4 channels, the electrical component produces high-quality output. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. The circuits in this analogue multiplexer number 4. Try searching for DG413 variants of the analog switch ic. An switch multiplexer with 50Ohm internal resistance has a value of 50Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. Users shouldn't supply more than 12V voltage to the switch device. Digital switch that provides Dual, Single power at a cost-effective price. 2.7V is the lowest voltage that should be fed to the electronic electronic part. This multiplexer would work with 1μA current. Putting voltage greater than 1μA on the multiplexer may cause damage. Despite this switch's dual supply capability, its voltage should not exceed 6V. For dual power supplies, a voltage of at least 3V should be attached. A 4 input needs to be operated. During operation, the multiplexer should not be exposed to a temperature above 85°C. The analogue multiplexer has 4 outputs. Suppliers offer a package with 16-TSSOP.
DG413LDQ-T1-E3 Features
4 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
-3db Bandwidth: 280MHz
DG413LDQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG413LDQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Imaging
- Communication systems
- Medical Instrumentation
- Audio and video signal routing
- Fiber to the Home
- E1 Multiplexer
- Private Branch Exchange (PBX)
- Avionics test equipment
- Channelized and Unchannelized DS3 applications
- Public switching systems
