DG413LDY-T1
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Weight | 547.485991mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 17Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 650mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Power Supplies | 3/12/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 50 ns |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 35 ns |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 280MHz |
| On-State Resistance (Max) | 17Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 19ns, 12ns |
| Charge Injection | 5pC |
| Crosstalk | -95dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 60ns |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG413LDY-T1 Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Temperatures around -40°C~85°C TA are extended for operation. A total of 16 terminations have been recorded. The electronic part provides high-quality output because it has 1 channels. A 5V voltage supply should turn on and run the electronic component. Electronic part bodies are injected with 16 pins. A SPST - NO/NC switching circuit is used for these analog switches. 4 circuits are used in this analogue multiplexer. In this multiplexer, the internal resistance is 17Ohm. Multiplexer or Switches is a typical switch device. A voltage higher than 12V should not normally be supplied to the switches. The analog switch ic is of the Dual, Single supply type and is cost-effective. 2.7V is the lowest voltage that should be fed to the electronic electronic part. Put voltage above 1μA on the multiplexer to cause damage. Despite this switch's dual supply capability, its voltage should not exceed 6V. A dual power supply should have at least 3V voltage attached. A total of SEPARATE OUTPUT outputs are available on this analog switch ic.
DG413LDY-T1 Features
1 Channels
Switch Circuit: SPST - NO/NC
-3db Bandwidth: 280MHz
DG413LDY-T1 Applications
There are a lot of Vishay Siliconix DG413LDY-T1 Analog Switches & Multiplexers ICs applications.
- Cell phones
- 65 V DACs
- Cable Modem
- Medical systems
- Avionics
- Precision test equipment
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Wireless Local Loop
- PCMCIA cards
- MP3 players
