DG413LDY-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Supplier Device Package | 16-SOIC |
| Weight | 547.485991mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 50Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 650mW |
| Base Part Number | DG413 |
| Number of Outputs | 4 |
| Number of Channels | 4 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Power Dissipation | 650mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 50 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 35 ns |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 280MHz |
| On-State Resistance (Max) | 17Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 19ns, 12ns |
| Charge Injection | 5pC |
| Crosstalk | -95dB @ 1MHz |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
DG413LDY-T1-E3 Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, this analog switch is mounted. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Increasing operating temperature to around -40°C~85°C TA. High-quality output is provided by the electronic component's 4 channels. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. A total of 4 circuits make up this switch device. Using the DG413 search parameter, you can discover variants of the switch. The internal resistance of this digital multiplexer is 50Ohm. To find out what the 16 pins do, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. The analog switch ic is of the Dual, Single supply type and is cost-effective. It is recommended that the electrical component receives a voltage of 2.7V. An operating current of 1μA would be sufficient for this switch device. When the digital multiplexer is charged above 1μA, damage can occur. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 6V. When using dual power supplies, you should attach at least 3V. Operating 4 inputs is required. In an environment with a temperature higher than 85°C, the digital switches should not operate. An output of 4 is provided by the digital multiplexer. Suppliers offer a package with 16-SOIC.
DG413LDY-T1-E3 Features
4 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
-3db Bandwidth: 280MHz
DG413LDY-T1-E3 Applications
There are a lot of Vishay Siliconix DG413LDY-T1-E3 Analog Switches & Multiplexers ICs applications.
- RGB switches
- Precision test equipment
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- PDAs
- Medical systems
- Transmit
- E1 Multiplexer
- Communications systems
- Audio/video switches
- PBXs
