DG4157DL-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 1.2Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG4157 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 50nA |
| Power Dissipation | 250mW |
| Max Supply Current | 500nA |
| Turn On Delay Time | 55 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 27 ns |
| -3db Bandwidth | 117MHz |
| On-State Resistance (Max) | 1.2Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 31 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 20pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 37ns, 23ns |
| Charge Injection | 50pC |
| Channel-to-Channel Matching (ΔRon) | 120m Ω (Max) |
| Crosstalk | -63dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 30ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG4157DL-T1-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a 6-TSSOP, SC-88, SOT-363. High reliability is achieved by using advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. A total of 6 terminations have been recorded. A 1 channel electronic part produces high-quality output. An 3V voltage supply should allow the electrical part to be turned on and run. 6 pins are injected to the electronic part body. Multiplexers built on a SPDT switching circuit are built. Look for analog switch ic variants by searching with DG4157. In this multiplexer, the internal resistance is 1.2Ohm. Please refer to the datasheets for 6 pins functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. Analogue multiplexer with a Single supply type that is cost-effective. There should be 1.65V voltage fed to the electrical part below 1.65V. It would be sufficient to run this analogue multiplexer with 50nA current. Using only a single voltage supply, this analog switch requires 1.65V~5.5V voltage. The switch multiplexer may be damaged if it is exposed to voltage greater than 500nA. Operating 1 inputs is required. In this digital multiplexer, there are 2 outputs.
DG4157DL-T1-E3 Features
1 Channels
Switch Circuit: SPDT
50nA Supply Current
-3db Bandwidth: 117MHz
DG4157DL-T1-E3 Applications
There are a lot of Vishay Siliconix DG4157DL-T1-E3 Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- ISDN NT1/TA
- MP3 players
- Communication systems
- Transmit
- Industrial and process control systems
- Cell phones
- SONET
- Communications systems
- Isolation
