DG417BAK-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-CDIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2016 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation | 600mW |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 82 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 62ns, 53ns |
| Charge Injection | 38pC |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
DG417BAK-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-CDIP (0.300, 7.62mm). This high-reliability packaging method uses advanced packaging methods Tube. In Through Hole, you'll find this switch device. Multiplexers and demultiplexers have the same number of circuits 1:1. Increasing operating temperature to around -55°C~125°C TA. In total, there have been 8 terminations. A high-quality output is provided by the electrical component's 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. An electrical component like this is included in the 8 series. These analog multiplexers are built based on SPST - NC switching circuits. A 35Ohm internal resistance characterizes this multiplexer. For functions related to 8 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. normally, users should not supply switches with voltages higher than 36V. There should be 13V voltage fed to the electrical part below 13V. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. It is recommended that you attach at least 7V to your dual power supply. There are SEPARATE OUTPUT outputs on this analog switch ic. Among the inputs that can be operated are the 1 inputs.
DG417BAK-E3 Features
1 Channels
Switch Circuit: SPST - NC
DG417BAK-E3 Applications
There are a lot of Vishay Siliconix DG417BAK-E3 Analog Switches & Multiplexers ICs applications.
- MP3 players
- Avionics test equipment
- Communications systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Isolation
- Cable Modem
- Fiber to the Home
- E1 Multiplexer
- Channel Banks
- Private Branch Exchange (PBX)
