DG417BDJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Weight | 930.006106mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 25Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 89 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 80 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 25Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 82 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 89ns, 80ns |
| Charge Injection | 38pC |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 35Ohm |
| Normal Position | NO |
| Height | 3.81mm |
| Length | 10.92mm |
| Width | 7.11mm |
| RoHS Status | Non-RoHS Compliant |
DG417BDJ Overview
This electronic part is conveniently packaged in 8-DIP (0.300, 7.62mm), making it easy to ship abroad. The advanced packaging method Tube provides high reliability. This analog switch is mounted in Through Hole. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operating temperature around -40°C~85°C TA extended. In total, 8 terminations have occurred. A high-quality output is provided by the electrical component's 1 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. This electrical component is included in the 8 series of products. Based on SPST - NC switching circuits, these analog multiplexers work. The circuits in this analogue multiplexer number 1. In this multiplexer, the internal resistance is 25Ohm. Please refer to the datasheets for 8 pins functions. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 36V should not normally be supplied to the switches. The digital multiplexer has a low cost Dual, Single supply. There should be 13V voltage fed to the electrical part below 13V. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. There is no problem with using dual supply voltage, but it should not exceed 22V. For dual power supplies, a voltage of at least 7V should be attached. 20V operating voltages are supported by the electronic component. It has a Drain to Source resistance of 35Ohm ohms.
DG417BDJ Features
1 Channels
Switch Circuit: SPST - NC
Drain-to-Source resistance: 35Ohm
DG417BDJ Applications
There are a lot of Vishay Siliconix DG417BDJ Analog Switches & Multiplexers ICs applications.
- High-Voltage
- Industrial
- RGB switches
- Relay replacements
- Battery-powered systems
- Cable PC
- Avionics and Military Systems
- Data Acquisition Systems
- Microwave transmission systems
- Avionics test equipment
